• 25 hp (20 kw) Kohler® Command Pro® EFI 747cc Engine
  • 60 in (152 cm) TURBO FORCE deck
  • The rear discharge design allows operators to trim on either side of the deck — no need to change direction to avoid discharging debris on roadways, sidewalks or flowerbeds.
  • EFI Fuel Efficiency - Kohler’s closed-loop EFI design improves fuel efficiency by up to 25 percent.

Z Master® 5000 Series - 25 hp Kohler® Command Pro EFI 747cc Engine with 60 in (152 cm) TURBO FORCE® Rear Discharge deck.

View Larger
7-Gauge, High-Strength Steel

The TURBO FORCE deck is constructed of 7-gauge, high-strength steel which is 33% thicker and 32% higher in yield strength than ordinary 10-gauge commercial steel used in 7/10 decks. The combined effect is 75% stronger, so it easily handles the most demanding conditions and resists damage from impacts and abrasion.

View Larger
Industry's Toughest Spindle Assemblies

Toro's rugged spindle assemblies survive impacts that would destroy lesser spindles. A stout cast iron housing with a massive base and six mounting bolts absorbs impact loads and distributes them across a broader area of the deck shell. Plus, the solid, one-inch diameter shaft is alloy steel, not the common lower-grade steel used in many competitive models.

72" Deck will have tapered bearing only.

View Larger
A Flat Crisp Cut with Precision Blades

(.250) thick precision blades resist flexing to provide a flat, crisp cut. High-strength, heat-treated alloy steel survives impacts and provides resistance to the rapid wear commonly associated with abrasive conditions. Options include Recycler® and Atomic® mulching blades, medium sail Bahai blades, and low sail sand blades.

View Larger
Deluxe Suspension Seat

Deluxe suspension seat features thick cushions, large bolsters and 3-D isolator mounts that absorb bumps and vibrations to reduce operator fatigue.

View Larger
Smarter design in a bull-nose bumper.

7-gauge bull-nose bumper not only protects against frontal impacts, but also contains an integral underskirt to minimize blowout of debris and dust. The bottom, leading edge of the deck is raised 1/4" (6 mm), allowing grass to stand more upright when entering the cutting chamber, ensuring a level cut. Leaf "plowing" during spring and fall clean-up also is significantly reduced.

View Larger
Smooth, Powerful Response

The new unitized pump and wheel motor use proven commercial hydraulic components while eliminating hoses and other potential leak points. You'll get a smoother, faster response while enjoying an even more reliable machine.

View Larger
Operator Information Center

The instrument panel includes a digital hour meter, fuel gauge, and voltage meter, as well as diagnostic indicators for the safety interlock system.

View Larger
Folding Rollover Protection System ROPS

A Rollover Protection System (ROPS), complete with seat belt, comes standard for operator protection in the case of accidental rollovers and tipovers. In situations where sufficient vertical clearance is not available, such as loading on an enclosed trailer, the ROPS can be temporarily unlocked and folded down.

View Larger
Convenience and Comfort

Operator controls are conveniently located. Large 1-5/8" (4.1 cm) diameter steering levers increase comfort and reduce fatigue. Handy storage compartment provides location for cell phone, tools, and more. Built-in cup holder provided.

  • Engine
    25 hp* (20 kw) Kohler® Command Pro EFI 747cc
  • Fuel Capacity
    Gasoline - 12 gal (45.4 L) single-point fill
  • Cutting Width
    60" (1.5 m)
  • Adjustable Discharge Baffle
    Standard
  • Air Filter
    Heavy-Duty Canister Air Cleaner
  • Armrests
    Standard
  • Blade Tip Speed
    18,500+ ft/min (5638.8 m/min)
  • Blade Type
    .25 in (.6 cm) thick heat-treated steel
  • Carrier Frame
    3 in x 1.5 in (7.6 cm x 3.8 cm) tubular steel
  • Caster Tires
    13 in x 6.5 in - 6 in (33 cm x 16.5 cm -15.2 cm) flat-free semi-pneumatic
  • Cup Holder
    Standard
  • Deck Design
    7-gauge 60 in (152 cm) TURBO FORCE® w/ bull-nose bumper
  • Discharge Chute
    Rubber
  • Drive System
    Hydraulic unitized pumps and wheel motors
  • Drive Tires
    23 in x 9.5 in -12 in (58.4 cm x 24.1 cm - 30.5 cm)
  • Ground Speed
    10 mph (16.1 kph) forward
  • Height of Cut
    1 in - 5.5 in (2.5 cm x 14 cm) by .25 in (.6 cm) increments
  • Number of Blades
    3
  • Hour Meter
    Standard
  • Hydraulic Fluid
    Premium synthetic
  • ROPS
    Folding; standard
  • Seat
    Deluxe suspensionwith 3-D Isolation Mounts
  • Spindle Bearings
    Greasable
  • Spindle Housing
    Cast iron
  • Steering Controls
    1.625 (4.1 cm) dia. levers; adjustable
  • Disclaimer
    *The gross horsepower of these engines was laboratory rated by the engine manufacturer in accordance with SAE J1940 or SAE J2723. As configured to meet safety, emission and operating requirements, the actual engine horsepower on these mowers will be significantly lower.
View Larger
Light Kit

The lights easily mount to the mower frame and wiring quickly connects to the existing accessory circuit.

Part # 107-9880 – 7000 Series and Z100-Z500
Part # 116-1154 – G3 and 3000/5000/6000 Series
Part # 130-8469 – 8000 Series Direct Collect Z
Part # 114-3505 – All Grandstands (2015 models and prior)
Part # 133-1437 – All Grandstands (2016 models)
Part # 133-1495 – All Grandstands (2016 models)

View Larger
Optional Blades

In addition to the high sail blade, which comes standard on Z Master® Z590 Series mowers, additional 1/4" (6 mm) blades are available to match regional and seasonal mowing conditions. Options include Recycler® and Atomic® mulching blades, medium sail Bahai blades, and low sail sand blades.

View Larger
Recycler® Mulching Kits

Recycler mulching kits deliver the industry's finest mulching performance and reduce mowing time up to 38% vs. bagging*.

*Respondents in a Texas A&M University study cut their lawns 38% faster when they didn't bag.

View Larger
Roller Striping Kit

Roller striping kit is easily installed and provides a premium "ball park" after-cut appearance.

View Larger
Toro Z Stand™

Exclusive Toro Z Stand provides an on-board tool to simply elevate the front end of the machine and provide access to the underside of the deck.

Part # 105-1622 Z Stand Kit – Z200, Z500, 7000 Series
Part # 117-0354 Z Stand Kit – 72" 5000/6000 Series (Excludes Rear Discharge 74944)
Part # 121-4811 Z Stand Kit – 48"-60" 2000/3000/5000/6000 Series

Select your serial number range from the options below to view parts & manuals.

Serial #
314000001-314999999
315000001-315999999
316000001-316999999