Série 4000 de 122 cm (48 po), 18 kW (24,5 cv), 852 cm³
Informations produit
- Numéro de modèle : 74000
- Numéro de série : 416266456 - 417499999
- Type de produit : Riding Products
Chargement...
Schémas d'assemblage
Rechercher une pièce dans des schémas d'assemblage :
-
Manuel d'entretien
-
Manuel de l'utilisateur
-
Catalogue de pièces
-
Garantie produit
-
Instructions d'installation
Z-Master Anti-Scalp Kit (Trim Side) (Réf. 108-4140)
Toro OEM anti-scalp deck wheels. These wheels help prevent the deck from coming in contact with the ground when passing over a high spot, thus preventing the blade from slicing off or "scalping" large clumps of grass.
Hypr-Oil™ 500 (quart) (Réf. 114-4713)
Hypr-oil™ 500 (quart). Toro Hypr-Oil 500 is a high-performance hydraulic fluid specifically formulated and approved by Toro engineering for use in Toro commercial zero turn mowers. It provides excellent wear and corrosion protection for hydraulic systems, helping to maintain consistent performance and extend the service life of hydraulic components. Always refer to your operator manual for the correct fluid specification and service intervals.
Hypr-Oil™ 500 (gallon) (Réf. 114-4714)
Toro Hypr-Oil 500 is a high-performance hydraulic fluid specifically formulated and approved by Toro engineering for use in Toro commercial zero turn and stand-on mower hydraulic systems. Maintaining the correct hydraulic fluid and changing it at the manufacturer-recommended interval is critical to protecting hydraulic pumps, wheel motors, and other hydraulic components from wear and corrosion — particularly on machines operating under commercial duty cycles. Refer to your operator manual for the correct change interval and fluid capacity for your equipment.
HYPR-OIL 500-5 GALLON (Réf. 114-4715)
Jack Kit With Adapter, Zero-Turn-Radius Side-Discharge or Rear-Dischar (Réf. 126-7282)
Jack Kit Adapter, Zero-Turn-Radius Side-Discharge or Rear-Discharge Ri (Réf. 126-7283)
Striper Kit (Réf. 126-7882)
Riding Mower Jack Kit (Réf. 127-6666)
Ce kit de cric pour tondeuse autoportée d’origine Toro® est conçu pour soulever et soutenir en toute sécurité votre tondeuse autoportée ou à rayon de braquage nul Toro. Vous avez ainsi un accès stable et sécurisé au dessous du tablier, pour changer les lames, remplacer les courroies et effectuer l’entretien courant. C'est l'un des accessoires les plus pratiques à l'achat pour tout nouveau propriétaire de tondeuse : investir dès le départ dans un cric approprié évite les méthodes de levage improvisées qui comportent des risques de blessure et d'endommagement du matériel. Avant de passer commande, vérifiez les numéros de modèle et de série de votre machine.
Pneus radiaux sans air pour gazon MICHELIN® X® TWEEL® (46 cm/24 po) (Réf. 139-3649)
A MICHELIN® X® TWEEL® airless radial tire is a single unit that replaces the current tire and wheel assembly. There is no need for complex mounting equipment and once they are bolted on, there is no air pressure to maintain The unique energy transfer within the poly-resin spokes helps reduce the “bounce” associated with pneumatic tires, while providing outstanding handling characteristics. The MICHELIN X TWEEL Turf airless radial tire is a single-unit assembly that replaces a conventional tire and wheel, eliminating the need for air pressure entirely — which means no flats, no downtime, and no patch kits. The wear life of a TWEEL tire is significantly longer than a comparable pneumatic tire, reducing the frequency of replacement and total cost of ownership over time. Verify your model and serial number to confirm the correct size before ordering.
48 inch Recycler Kit (GrandStand) (Réf. 139-6650)
Ce kit Recycler® de 122 cm (48 po) d’origine Toro® est conçu spécifiquement pour les tondeuses à conducteur debout Toro GrandStand®. Il transforme le tablier en mode de déchiquetage Recycler® complet. Une fois installé, le système Recycler® breveté coupe les brins d’herbe entre 6 et 8 fois, puis les réinjecte dans la pelouse sous forme de fines particules d’engrais naturel, riche en nutriments. Ainsi, dans la plupart des conditions, il n’y a plus besoin de ramasser ou de ratisser l’herbe coupée. L'une des améliorations les plus populaires lors de l'achat pour les nouveaux propriétaires de GrandStand® qui souhaitent maximiser la valeur de leur machine dès le premier jour. Avant de passer commande, vérifiez les numéros de modèle et de série de votre machine.
16.5 Inch Hi-Flow Blade (Réf. 140-1243)
This Toro OEM 16.5-inch Hi-Flow replacement mower blade is designed to produce high lift, cutting grass cleanly and propelling clippings upward and out through the discharge chute. Hi-Flow blades — also referred to as basic, standard, or 2-in-1 blades — are the preferred choice when using a grass catcher or bagger, as the increased airflow drives clippings efficiently into the collection bag. This blade is compatible with multiple Toro riding lawn mowers models — always verify your model and serial number before ordering to confirm the correct fit.
16.5 Inch Medium Flow Blade (Réf. 140-4860)
This Toro OEM 16.5-inch Mid Flow replacement mower blade is engineered to provide a balance between the high suction of Hi-Flow blades and the minimal airflow of Low Flow blades. Mid Flow blades have a slight upward angle on the cutting edges, producing moderate lift while requiring less horsepower than Hi-Flow blades — making them a versatile option for varied terrain and grass conditions. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
16.5 Inch Low Flow Blade (Réf. 140-4861)
This Toro OEM 16.5-inch Low Flow replacement mower blade features a slightly curved tip design that keeps airflow to a minimum during operation. Low Flow blades are the right choice for mowing in sandy, dusty, or dry conditions where high suction would stir up excessive debris — they also cause less strain on the engine than Hi-Flow blades, making them a practical option when horsepower is a consideration. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
16.5 Inch Atomic Blade (Réf. 140-4862)
This Toro OEM 16.5-inch Atomic replacement blade — commonly known as a Gator-style blade — features a serrated cutting edge with raised teeth that shred grass clippings into much finer pieces than a standard mulching blade. The serrated design re-cuts clippings multiple times on every pass, delivering the highest mulching quality available and a consistently crisp, clean cut even in dense or damp grass. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
16.5 Inch Recycler Blade (Réf. 140-4863)
This Toro OEM 16.5-inch Recycler replacement mower blade is built to work within Toro's Recycler mulching system, featuring uniquely shaped 'accelerator' wings that act as a fan to keep clippings circulating beneath the deck. As clippings are forced back into the cutting zone, they are re-cut multiple times into fine pieces that fall back into the lawn and break down into natural fertilizer — feeding the grass and reducing the need to bag or rake. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Hi-Flow 16.5 Inch Blade Pack (6) (Réf. 140-4887)
This Toro OEM 16.5-inch Hi-Flow replacement mower blade — sold as a pack of 6 is designed to produce high lift, cutting grass cleanly and propelling clippings upward and out through the discharge chute. Hi-Flow blades — also referred to as basic, standard, or 2-in-1 blades — are the preferred choice when using a grass catcher or bagger, as the increased airflow drives clippings efficiently into the collection bag. This blade is compatible with multiple Toro riding lawn mowers models — always verify your model and serial number before ordering to confirm the correct fit.
Mid Flow 16.5 Inch Blade Pack (6) (Réf. 140-4888)
This Toro OEM 16.5-inch Mid Flow replacement mower blade — sold as a pack of 6 is engineered to provide a balance between the high suction of Hi-Flow blades and the minimal airflow of Low Flow blades. Mid Flow blades have a slight upward angle on the cutting edges, producing moderate lift while requiring less horsepower than Hi-Flow blades — making them a versatile option for varied terrain and grass conditions. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Low Flow 16.5 Inch Blade Pack (6) (Réf. 140-4889)
This Toro OEM 16.5-inch Low Flow replacement mower blade — sold as a pack of 6 features a slightly curved tip design that keeps airflow to a minimum during operation. Low Flow blades are the right choice for mowing in sandy, dusty, or dry conditions where high suction would stir up excessive debris — they also cause less strain on the engine than Hi-Flow blades, making them a practical option when horsepower is a consideration. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Atomic 16.5 Inch Blade Pack (6) (Réf. 140-4890)
This Toro OEM 16.5-inch Atomic replacement blade — commonly known as a Gator-style blade — features a serrated cutting edge with raised teeth that shred grass clippings into much finer pieces than a standard mulching blade. The serrated design re-cuts clippings multiple times on every pass, delivering the highest mulching quality available and a consistently crisp, clean cut even in dense or damp grass. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Recycler 16.5 Inch Blade Pack (6) (Réf. 140-4891)
This Toro OEM 16.5-inch Recycler replacement mower blade — sold as a pack of 6 is built to work within Toro's Recycler mulching system, featuring uniquely shaped 'accelerator' wings that act as a fan to keep clippings circulating beneath the deck. As clippings are forced back into the cutting zone, they are re-cut multiple times into fine pieces that fall back into the lawn and break down into natural fertilizer — feeding the grass and reducing the need to bag or rake. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Front Light Kit - 4000 Series (Réf. 144-0389)
This Toro OEM LED light kit is designed to extend your working day by providing reliable illumination during low-light mowing conditions. Verify your model and serial number to confirm compatibility before ordering.
TRIMMER MOUNT (Réf. 144-2665)
KIT, JACK MOUNT (Réf. 144-2676)
48" CHUTE GATE KIT [4000] (Réf. 144-2688)
Handle Extension Kit (Réf. 145-3615)
Genuine OEM Part
ASM-VOODOO TRAC 24X9.5-12 (Réf. 147-5029)
BLADE-16.50 HIGH FLOW (Réf. 147-6250)
6 PACK-BLADE, 16.50 HIGH FLOW (Réf. 147-6254)
MICHELIN® X® TWEEL® Turf Airless Caster Wheels (13") (Réf. 147-6294)
The MICHELIN® X® TWEEL® Turf Caster Wheel is the next “revolution” in commercial mowing. The MICHELIN X TWEEL Turf Caster Wheel has all the qualities you would want in a pneumatic tire but it never needs air. No more flats, downtime, patch kits or replacement tires. And in the area of wear and tear, this “tire” has a wear life that is three times that of a pneumatic.
Bucket Mount Kit, Z Master 2000 or 4000 Series Riding Mower (Réf. 147-6345)
Universal Mount Kit, Z Master 2000 or 4000 Series Riding Mower (Réf. 147-6346)
Kit-Baffle, Turbo Force 48 (Réf. 147-7360)
KIT-ELEC DECK LIFT (Réf. 147-7867)
KIT-2IN RECIEVER HITCH (Réf. 161-2810)
KIT-ACTUATOR REPLACEMENT,412200557 BE (Réf. 161-3549)
KIT-ELEC DECK LIFT, SN 412200557 BELO (Réf. 161-3550)
Fuel Pickup with Screen, Kit (Réf. 161-6806)
Rear Weight Kit (Réf. 163-7435)
Spark Arrestor Screen (Réf. 75-6880)
BAGGER KIT, Z MASTER 2000 / 4000 (Réf. 78439)
4000 Series E-Z Vac Blower & Drive Kit for 48" Deck (Réf. 78464)
4000 Series E-Z Vac Blower & Drive Kit for 48" Deck - use with 4000 Series Twin Soft Bagger 48 - 60" Deck (#78463)
-
Numéro de modèle
74000 -
Numéro de série
416266456 - 417499999 -
Nom du produit
Série 4000 de 122 cm (48 po), 18 kW (24,5 cv), 852 cm³ -
Marque du produit
Toro -
Type de produit
Riding Products -
Série de produit
Zero Radius Turn, Commercial 4000 Series -
Type de Châssis
ZRT - LCE -
Largeur de travail
48 inch / 122 cm -
Éjection
Side Discharge -
Fabricant du moteur
Kawasaki -
Taille de moteur
24.5 hp -
Type de moteur
4 Cycle -
Démarreur
Electric -
Type de transmission
Hydrostatic -
Type de Traction
Rear WD
-
Engine: Battery
12V 300CCA -
Engine: Engine Speed
3600±100 RPM -
Engine: Spark Plug
NGK BPR4ES -
Engine: Spark Plug Gap
.030"/ .76mm -
Chassis: Tire Pressure
13 psi / 90 kPa -
Engine: Engine Oil Type
filter chg 77 oz.(2.3 L); no filter chg 70 oz.(2.1 L); 10W-30 above -4F(-20C) or 5W-20 below 32F(0C) -
Drive System: Ground Speed
0-10 mph / 0-16kph -
Chassis: Height of Cut Range
1.5" - 5.5" (38-140mm) -
Engine: Ignition Coil Air Gap
0.011in (0.3mm) -
Drive System: Gearbox Lubricant
HYPR-OIL 500 / 20w-50 Synthetic Motor Oil