5000 Series 60 in. (152 cm) 25.5 hp 852cc
Product Information
- Model #: 72910
- Serial #: 418000000 - 419999999
- Product Type: Riding Products
Loading...
Assembly Drawings
Search for a part within assembly drawings:
-
Service Manual
-
Operator's Manual
-
Parts Catalog
-
Product Warranty
-
Setup Instructions
GrandStand Turbo Baffle Kit (Part # 107-1634)
This genuine Toro OEM turbo baffle kit is designed for Toro GrandStand stand-on mowers and modifies the airflow under the cutting deck to improve clipping discharge performance in heavy, dense, or wet grass conditions. The turbo baffle redirects air movement beneath the deck to increase the velocity at which clippings are expelled through the discharge chute, reducing the tendency for clippings to clump or block in challenging mowing conditions. Verify your model and serial number before ordering.
Z-Master Anti-Scalp Kit (Trim Side) (Part # 108-4140)
This genuine Toro OEM anti-scalp deck wheel kit covers the trim side of the Toro Z-Master mower deck — the side closest to obstacles and edges. Anti-scalp wheels on the trim side prevent the deck from digging into raised spots when mowing close to beds, driveways, and curbs where the deck is most likely to make ground contact. Inspect regularly and replace when wheels are cracked, broken, or no longer rotating freely. Verify your model and serial number before ordering.
Please contact your local dealer
Hypr-Oil™ 500 (quart) (Part # 114-4713)
Hypr-oil™ 500 (quart). Toro Hypr-Oil 500 is a high-performance hydraulic fluid specifically formulated and approved by Toro engineering for use in Toro commercial zero turn mowers. It provides excellent wear and corrosion protection for hydraulic systems, helping to maintain consistent performance and extend the service life of hydraulic components. Always refer to your operator manual for the correct fluid specification and service intervals.
Hypr-Oil™ 500 (gallon) (Part # 114-4714)
Toro Hypr-Oil 500 is a high-performance hydraulic fluid specifically formulated and approved by Toro engineering for use in Toro commercial zero turn and stand-on mower hydraulic systems. Maintaining the correct hydraulic fluid and changing it at the manufacturer-recommended interval is critical to protecting hydraulic pumps, wheel motors, and other hydraulic components from wear and corrosion — particularly on machines operating under commercial duty cycles. Refer to your operator manual for the correct change interval and fluid capacity for your equipment.
Hypr-Oil™ 500 Hydraulic Oil (5 gallon) (Part # 114-4715)
Toro Hypr-Oil 500 is a high-performance hydraulic fluid formulated and approved by Toro engineering for commercial zero turn and stand-on mower hydraulic systems. The 5-gallon commercial bulk pack is designed for fleet operators and service shops performing multiple machine hydraulic fluid changes. Maintaining the correct hydraulic fluid on schedule protects pumps, wheel motors, and other hydraulic components from accelerated wear. Refer to your operator manual for the correct change interval and capacity for each machine. Do not mix with other hydraulic fluids.
Bimini Folding Sunshade Assembly (Part # 115-4510)
Toro genuine Optional fabric sun shade provides protection and comfort by shielding the operator from the elements. Verify your model and serial number to confirm compatibility before ordering.
Roller Striping Kit (Part # 115-7470)
Toro OEM A mower striping kit. The ultimate way to enhance the striping ability of your Z-Master. The Toro OEM striping kit creates defined light and dark stripes in your lawn by pressing grass down in the direction of travel as you mow — the contrast in light reflection produces the 'ballpark' stripe effect. The kit's downward pressure is adjustable, allowing you to vary the intensity of the stripe. Verify your model and serial number to confirm compatibility before ordering.
Seat Cover w/Arm Rest (Part # 117-0095)
This genuine Toro OEM seat cover with arm rest is designed to fit Toro Z-Master zero turn mowers and serves a dual purpose: protecting the operator seat from UV and wear from day one, or replacing a worn or damaged seat cover as a wear-and-tear item. The arm rest addition improves operator comfort significantly during longer mowing sessions. Verify your model and serial number before ordering.
Operator-Controlled Discharge Chute Kit (Part # 117-3600)
This genuine Toro OEM operator-controlled discharge chute kit allows the operator to open and close the mower's discharge chute directly from the controls while mowing — without stopping, dismounting, or manually adjusting the chute. This significantly reduces the time and effort required to redirect clippings when mowing near driveways, flowerbeds, and pedestrian areas. A popular purchase-stage upgrade for operators who do precise or complex mowing. Verify your model and serial number before ordering.
Z Stand Kit for Z Master Riding Mower with 48", 52" or 60" Deck (Part # 121-4811)
This genuine Toro OEM Z Stand deck stand kit is designed for Toro Z-Master zero turn mowers with 48", 52", or 60" decks. It allows operators and technicians to quickly and safely access the underside of the mower deck for blade changes, belt replacement, and routine maintenance — without needing a full mower jack or lift. Widely used in professional service environments and by commercial operators who need fast, reliable under-deck access in the field. Verify your model and serial number before ordering.
Suspension Seat and Mount Kit (Part # 121-7596)
Toro suspension seat increases operator comfort and boosts productivity in ways you’ve never imagined. Mow longer without stopping and cut around even the most intricate landscaping at faster speeds with better results. This Toro OEM replacement seat is designed to restore operator comfort on your Toro riding mower. Verify your model and serial number to confirm compatibility before ordering.
Riding Mower Jack Kit (Part # 127-6666)
This genuine Toro OEM riding mower jack kit is designed to safely lift and support your Toro riding mower or zero turn, giving you safe, stable under-deck access for blade changes, belt replacements, and routine maintenance. It is one of the most practical purchase-stage accessories for any new mower owner — investing in a proper jack from day one avoids improvised lifting methods that risk injury and equipment damage. Verify your model and serial number before ordering.
Power Deck Lift Kit (Part # 132-5986)
Easily Raise and Lower your Z-Master cutting deck with the push of a button using this Toro power lift kit. Toro operator controlled discharge kit. This Toro OEM discharge chute kit allows the operator to direct or block the flow of clippings from the mower deck, helping to prevent debris from reaching flower beds, driveways, or bystanders. Verify your model and serial number to confirm compatibility before ordering.
Please contact your local dealer
Titan HD Series Bucket Mount Kit (Part # 137-9216)
Toro OEM bucket mount kit. Saves you time, money, and hassle when you’re in the seat trying to get the day's cutting done. Verify your model and serial number to confirm compatibility before ordering.
Trimmer Mount Kit (Part # 137-9769)
Toro OEM trimmer mount kit. Keep your trimmer securely mounted on your riding mower. Verify your model and serial number to confirm compatibility before ordering.
60 Inch Recycler Kit (Part # 139-6655)
Recycler Kit, when installed on compatible 42 in. deck Toro zero turn riding mowers, gives it the capability to mulch grass by cutting it multiple times turning it into fine clipping pieces. Verify your model and serial number to confirm compatibility before ordering.
MICHELIN® X® TWEEL® Turf Airless Radial Tires (24") (Part # 139-7891)
The MICHELIN® X® TWEEL® Turf Airless Radial Tires are the next “revolution” in commercial mowing has arrived. The MICHELIN X TWEEL Turf Airless Radial Tire has all the qualities you would want in a pneumatic tire but it never needs air. The MICHELIN X TWEEL Turf airless radial tire is a single-unit assembly that replaces a conventional tire and wheel, eliminating the need for air pressure entirely — which means no flats, no downtime, and no patch kits. The wear life of a TWEEL tire is significantly longer than a comparable pneumatic tire, reducing the frequency of replacement and total cost of ownership over time. Verify your model and serial number to confirm the correct size before ordering.
Please contact your local dealer
20.5 Inch Hi-Flow Blade (Part # 140-1240)
This Toro OEM 20.5-inch Hi-Flow replacement mower blade is designed to produce high lift, cutting grass cleanly and propelling clippings upward and out through the discharge chute. Hi-Flow blades — also referred to as basic, standard, or 2-in-1 blades — are the preferred choice when using a grass catcher or bagger, as the increased airflow drives clippings efficiently into the collection bag. This blade is compatible with multiple Toro riding lawn mowers models — always verify your model and serial number before ordering to confirm the correct fit.
20.5 Inch Atomic Blade (Part # 140-1241)
This Toro OEM 20.5-inch Atomic replacement blade — commonly known as a Gator-style blade — features a serrated cutting edge with raised teeth that shred grass clippings into much finer pieces than a standard mulching blade. The serrated design re-cuts clippings multiple times on every pass, delivering the highest mulching quality available and a consistently crisp, clean cut even in dense or damp grass. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
20.50 Inch Medium Flow Blade (Part # 140-4853)
This Toro OEM 20.5-inch Mid Flow replacement mower blade is engineered to provide a balance between the high suction of Hi-Flow blades and the minimal airflow of Low Flow blades. Mid Flow blades have a slight upward angle on the cutting edges, producing moderate lift while requiring less horsepower than Hi-Flow blades — making them a versatile option for varied terrain and grass conditions. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
20.50 Inch Low Flow Blade (Part # 140-4854)
This Toro OEM 20.5-inch Low Flow replacement mower blade features a slightly curved tip design that keeps airflow to a minimum during operation. Low Flow blades are the right choice for mowing in sandy, dusty, or dry conditions where high suction would stir up excessive debris — they also cause less strain on the engine than Hi-Flow blades, making them a practical option when horsepower is a consideration. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
20.5 Inch Recycler Blade (Part # 140-4855)
This Toro OEM 20.5-inch Recycler replacement mower blade is built to work within Toro's Recycler mulching system, featuring uniquely shaped 'accelerator' wings that act as a fan to keep clippings circulating beneath the deck. As clippings are forced back into the cutting zone, they are re-cut multiple times into fine pieces that fall back into the lawn and break down into natural fertilizer — feeding the grass and reducing the need to bag or rake. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Hi-Flow20.5 Inch Blade Pack (6) (Part # 140-4877)
This Toro OEM 20.5-inch Hi-Flow replacement mower blade — sold as a pack of 6 is designed to produce high lift, cutting grass cleanly and propelling clippings upward and out through the discharge chute. Hi-Flow blades — also referred to as basic, standard, or 2-in-1 blades — are the preferred choice when using a grass catcher or bagger, as the increased airflow drives clippings efficiently into the collection bag. This blade is compatible with multiple Toro riding lawn mowers models — always verify your model and serial number before ordering to confirm the correct fit.
Mid Flow 20.5 Inch Blade Pack (6) (Part # 140-4878)
This Toro OEM 20.5-inch Mid Flow replacement mower blade — sold as a pack of 6 is engineered to provide a balance between the high suction of Hi-Flow blades and the minimal airflow of Low Flow blades. Mid Flow blades have a slight upward angle on the cutting edges, producing moderate lift while requiring less horsepower than Hi-Flow blades — making them a versatile option for varied terrain and grass conditions. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Low Flow 20.5 Inch Blade Pack (6) (Part # 140-4879)
This Toro OEM 20.5-inch Low Flow replacement mower blade — sold as a pack of 6 features a slightly curved tip design that keeps airflow to a minimum during operation. Low Flow blades are the right choice for mowing in sandy, dusty, or dry conditions where high suction would stir up excessive debris — they also cause less strain on the engine than Hi-Flow blades, making them a practical option when horsepower is a consideration. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Atomic 20.5 Inch Blade Pack (6) (Part # 140-4880)
This Toro OEM 20.5-inch Atomic replacement blade — commonly known as a Gator-style blade — features a serrated cutting edge with raised teeth that shred grass clippings into much finer pieces than a standard mulching blade. The serrated design re-cuts clippings multiple times on every pass, delivering the highest mulching quality available and a consistently crisp, clean cut even in dense or damp grass. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Recycler 20.5 Inch Blade Pack (6) (Part # 140-4881)
This Toro OEM 20.5-inch Recycler replacement mower blade — sold as a pack of 6 is built to work within Toro's Recycler mulching system, featuring uniquely shaped 'accelerator' wings that act as a fan to keep clippings circulating beneath the deck. As clippings are forced back into the cutting zone, they are re-cut multiple times into fine pieces that fall back into the lawn and break down into natural fertilizer — feeding the grass and reducing the need to bag or rake. Compatible with multiple Toro riding lawn mowers models — verify your model and serial number before ordering.
Riding Mower Toeboard Weights (Part # 140-4958)
This genuine Toro OEM toeboard weight kit adds front ballast to your Toro riding mower, improving traction and steering stability on slopes and uneven terrain. Insufficient front weight on a riding mower can cause the steering wheels to lose traction on steep ground, reducing control and increasing the risk of sliding. Adding toeboard weights is a practical upgrade for any owner who regularly mows on slopes. Verify your model and serial number before ordering.
Please contact your local dealer
Titan Deluxe Cover (Part # 490-7319)
Toro OEM deluxe rider cover keeps your Titan riding lawn mower protected from the elements when not in use. Cover is made to withstand wear and tear and features elastic cord to keep cover in place. This Toro OEM mower cover is made from durable, weather-resistant material to protect your equipment from rain, sun, dust, and debris during storage. Verify your model and serial number to confirm the correct cover for your equipment.
Rider Arm Rest Bag (Part # 490-7320)
This genuine Toro OEM replacement part is manufactured to the exact engineering specifications of your Toro equipment, ensuring correct fit and reliable performance. Verify your model and serial number to confirm compatibility before ordering.
Z-Master Spark Arrestor (Part # 75-6880)
Toro OEM spark arrestor prevents carbon build ups from being ejected from the engine and igniting a fire. Verify your model and serial number to confirm compatibility before ordering.
Blower and Drive Kit, 60in E-Z Vac for Z Master G3 Mower (Part # 78553)
60in E-Z Vac Triple Bagging System, Z Master G3 Mower (Part # 78563)
60in E-Z Vac DFS Collection System, Z Master G3 Mower (Part # 78567)
Filter Gauge for Kohler Engines (Part # 99-4664)
Toro genuine filter gauge. Toro would like to remind you that fitment can vary by sub model, serial number, and/or production date of your equipment. Verify your model and serial number to confirm compatibility before ordering.
-
Model #
72910 -
Serial #
418000000 - 419999999 -
Product Name
5000 Series 60 in. (152 cm) 25.5 hp 852cc -
Product Brand
Toro -
Product Type
Riding Products -
Product Series
Zero Radius Turn, Professional 5000 Series -
Chassis Type
ZRT - LCE -
Swath
60 inch / 152 cm -
Discharge
Side Discharge -
Engine/Motor Manufacturer
Kawasaki -
Engine/Motor Type
4 Cycle -
Engine Starter
Electric -
Transmission Type
Hydrostatic -
Traction Type
Rear WD
-
Engine: Battery
12V 300CCA -
Engine: Spark Plug
NGK BPR4ES -
Engine: Spark Plug Gap
.030"/ .76mm -
Chassis: Tire Pressure
13 psi / 90 kPa -
Chassis: Height of Cut Range
1" - 5.5" (25-140mm) -
Engine: Engine Oil Type
filter chg 77 oz.(2.3 L); no filter chg 70 oz.(2.1 L); 10W-30 above -4F(-20C) or 5W-20 below 32F(0C) -
Drive System: Ground Speed
0-10 mph / 0-16kph -
Drive System: Gearbox Lubricant
HYPR-OIL 500 / 15w-50 Synthetic Motor Oil -
Engine: Ignition Coil Air Gap
0.011in (0.3mm) -
Engine: Engine Speed
3750+/-50 RPM